Editorial

Diagnostic setup proposed by H.D. Kingsley serves as a practical aid in treatment planning and diagnosis. These setups have some inherent shortcomings. A simple technique of duplication of the setups in dental stone can solve problems encountered before as well as provide many other advantages over the conventional procedure. The diagnostic setup is prepared by the conventional method [Figure 1]. An alginate impression is then taken of the setups and poured in dental stone to obtain the derived treatment model [Figure 2]. The same setup can now be further modified for alternate lines of treatment. Subsequently models could then be obtained as required [Figure 3].

Purpose Irregularity accounts for interproximal contact point displacements and can be measured using a variety of techniques. The aim of this study was to evaluate the validity and reliability of three methods in relation to the “gold standard” of manual caliper measurements of plaster study casts. Materials And Methods Six mandibular study casts representing varying degrees of anterior crowding were measured by the same observer using four methods over the course of 5 weeks. Validity was statistically assessed with single sample statistical testing by the cast, method, and week (or combinations) and reliability was tested using intraclass reliability coefficient. Results The three noncaliper techniques demonstrated validity (P > 0.05) when the caliper method mean was used as the set value, but the three noncaliper methods produced means that were significantly greater when mean differences among techniques were compared to hypothetical zero. However, none of the differences were clinically significant (>0.5 mm). High reliability (reproducibility) was demonstrated (P > 0.05) with both aggregated and nonaggregated mean differences. Conclusions Reliability of measuring irregularity index with any of the four methods tested was high, but the validity of techniques compared to the “gold standard” method of manual caliper measurements of plaster study casts should continue to be questioned. Differences among the techniques were not clinically significant or important.

Aims The aim of this study was to evaluate the biomechanical effects on the craniofacial complex of skeletal anchorage and dental anchorage during face mask therapy. Subjects And Methods Two nonlinear finite element (FE) simulations were performed using a three-dimensional FE model. Face mask therapy with dental anchorage in the upper canines and face mask therapy with skeletal anchorage in the piriform apertures of the maxilla were simulated. In both simulations, the magnitude of the applied force was 750 g per side, and the force direction was 30° forward and downward relative to the occlusal plane. Results The circummaxillary sutures showed greater and more uniform stresses in the skeletal anchorage model than the dental anchorage model. This is the result of the more parallel forward movement of the maxilla in the skeletal anchorage model. Conclusions In Class III malocclusions with maxillary deficiency, for improved effects on the maxilla, choosing skeletal anchorage may be more effective in face mask therapies

Objectives The aim of this study was to compare the shear bond strength (SBS) of brackets systems with four different base technologies. Materials And Methods Maxillary first premolars were randomly divided into four groups of thirty specimens each: (1) Master Series™ conventional twin, (2) T3™ self-ligating, (3) Victory series™ conventional twin, and (4) H4™ self-ligating brackets. Maxillary first premolars were bracketed using an acid-etch composite system, and the SBS measured using an Instron Universal Testing Machine at a crosshead speed of 2 mm/min. The ANOVA and Tukey’s multiple comparison tests were performed with significance predetermined at P = 0.05. Results The overall mean bond strengths were 8.49 ± 2.93, 10.85 ± 3.34, 9.42 ± 2.97, and 9.73 ± 2.62 for the Groups 1, 2, 3, and 4 brackets, respectively. One-way ANOVA test gave an F = 3.182 with a P = 0.026. The Group 1 and Group 2 were observed to have statistically significant difference with a P = 0.014. Conclusions The T3 self-ligating one-piece design with microetched Quadra Grip™ base brackets had the highest bond strength. The SBS difference between Group 2, Group 3, and Group 4 was not significant, but the difference between Group 2 and Group 1 was statistically significant.

Background In this study, we aimed to evaluate the inclination of orthodontic research published in original articles in three of the most popular and recognized orthodontic journals with high impact factor; American Journal of Orthodontics and Dentofacial Orthopedics (AJODO), the Angle Orthodontist (AO), and European Journal of Orthodontics (EJO) published in a 5-year duration time frame (2010–2014). Materials And Methods Online search with supplementary hand searching was undertaken for original research articles in these three orthodontic journals from 2010 to 2014. Classification of data was completed autonomously by manual and direct appraisal of the manuscript of each journal. Results And Conclusion Three thousand one hundred and forty articles published in AJODO, AO, and EJO in the particular time period were selected, out of which 1783 original research study articles (56.78%) were appraised for classification in their various respective knowledge domains. AO (82.73%) and EJO (76.99%) were relatively more committed toward publication of research work in comparison to AJODO (34.55%). Research articles based on perception and questionnaires (12%), temporary anchorage devices (11%), cone-beam computed tomography (8%), invisible orthodontics (lingual orthodontics, clear aligners, esthetic brackets, and wires) (5%), and airway examination (5%) were the five most recurrently selected subjects of interest (41%) in these three journals during the observation period. The total number of research articles published in the three journals reduced statistically significantly in 2014 when compared to 2010.

As the whole world gets more digital, so do we. This article provides a basic know-how for the CAD/CAM-workflow for metallic orthodontic appliances. Demonstrating step-by-step how to design the appliance on a digital cast and laser-melting (3D metal printing) it, till the final result, without any physical models.

Introduction Angular photogrammetric soft tissue facial profile analysis provides a permanent record for the actual appearance of a person, which would also serve to establish an ideal esthetic treatment goal. The aim of the present study was to evaluate the average angular variables that define the soft tissue facial profile of a Bangladeshi sample. Materials And Methods This cross-sectional study was carried out at Department of Orthodontics and Dentofacial Orthopedics of Dhaka Dental College and Hospital, Bangladesh, from July to December 2015. Soft tissue facial profiles of 200 participants (100 males and 100 females) between 18 and 25 years of age, with a dental Class I occlusal relationship and harmonious soft tissue profile, were selected by convenience sampling among students, doctors, and patients of Dhaka Dental College. Standardized photographs of 200 samples were taken in the natural head position. The photographic records were analyzed with the software for Windows, Microsoft Visio 2007, Standard Edition. All data were analyzed through standard methods using Statistical Package for the Statistical Package for Social Science Software (SPSS Version-20, IBM Corp, USA). Results The average angular measurements for nasofrontal, total facial angle, facial angle, upper lip angle, projection of lower lip to chin, and mentolabial angle were wider in females. The mean value for nose tip angle, nasolabial angle, nasomental angle, and projection of upper lip to chin angle was higher in males compared to females. Nasofrontal angle (G-N-Nd) (P = 0.000) and mentolabial angle (Li-Sm-Pg) (P = 0.001) showed statistically significant differences. The greatest variability was found for mentolabial angle. Conclusion The study of angular photogrammetric soft tissue facial profile analysis of Bangladeshi young adults contributes to the establishment of standardized normal values for the population. This study provides data which can be used in treatment planning by specialists such as orthodontists, prosthodontists, plastic surgeons, and maxillofacial surgeons, who have the capability to change the soft tissue facial features.